Configure mms on android mts. How do I open an MMS message on my phone? How to set the MMS option manually

The article describes how to configure MMC for the Android operating system.

Navigation

The ability to send MMS from certain mobile devices is no longer some kind of special technical service provided for a lot of money. MMS can be sent with the same simplicity as SMS, but for this, of course, your gadget must be configured accordingly. In this review, we will discuss how to configure a mobile device running an operating system “ Android”To send MMS messages.

How to set up a gadget running “Android” to send MMS?

First, let's figure out what configuration methods we have in order to send MMS to “ Android”:

1. Automatic tuning
2. Setting up by calling a specialist
3. Manual setting
4. Configuration using a computer and the Internet

I would like to add that the very need to configure MMS to “ Android”, As a rule, occurs in the following cases:

1. Factory settings have been reset
2. A new gadget was purchased

How to configure a gadget running “Android” to send MMS using automatic settings?

The most simple method MMS settings to “ Android”Is, of course, automatic tuning. That is, in this case, we need to perform a minimum of actions, the rest will be done by the system “ Android”Yourself. But similar way settings is valid the first time your gadget is registered on the network of any mobile operator.

How to set up MMS on Android?

You need to take the following steps:

1. Install a SIM card in the gadget
2. Turn on the gadget (if you need a pin code, then enter it), wait until the registration process is completed, and an SMS with the settings will be sent to your mobile device
3. After receiving the settings for your gadget, you will need to accept and save them. After restarting the gadget, your mobile device is running “ Android”Will be ready to work with MMS

How to set up a gadget running "Android" to send MMS by calling a specialist?

You can contact a specialist for MMC settings on your gadget for help every time you need it. True, you already have to take more actions than in the previous method.

To set the MMS to “ Android”With the help of a specialist, you need to call your mobile operator:

• « Megaphone"- to the number 0550
• « MTS"- to the number 8900
• « Beeline"- to the number 0611
• « Tele 2"- to the number 611

After the call, we will go to the voice menu (applies to all mobile operators) and follow the instructions of the answering machine. Then we will be contacted by a specialist of the company we have chosen, who needs to read out his passport data to identify our person. After that, the specialist will send the tinctures to our phone. Next, you should proceed as in the previous case - accept and save the settings, and also restart the gadget. In some cases, you will need to call the specialist again and ask him to activate the settings on his SIM card.

How to set up a gadget running "Android" to send MMS manually?

If you purchased your gadget a long time ago, and also cannot get through to a specialist, then you need to set the MMS to “ Android”Manually.

For this you need:

1. Go to the gadget menu
2. Then go to « Settings»
3. Then go to the item " Networks" or " More"Depending on the gadget model
4. Then you need to click on " Mobile networks»
5. Go to " Access points"And choose" Mobile data»
6. Then choose “ Internet access points"And click on" New access point»

Then you have to enter certain data, which may differ for each mobile operator. The table below shows which data should be entered in each specific case:

Enter the specified data, save the settings and reboot the gadget. Now your mobile device is on “ Android”Ready to work with MMS.

How to set up a gadget running “Android” to send MMS using a computer and the Internet?

If you don't want to dig into your phone, then set up MMS to “ Android”Is possible with a computer connected to the Internet. To do this, we need to go to the website of our mobile operator and select the appropriate section.

In this review, we have laid out all possible ways MMC settings on your gadget running “ Android”. If the listed methods do not work, then you did something wrong.

Video: Internet and MMS settings for Android phones

The MMS function is supported by many modern phone models. The ability to send multimedia messages allows mobile phone users to share with each other their impressions of rest, walking, wish a great mood along with a beautiful melody or an interesting picture. This function is actively used today by those subscribers who are owners of old models cell phones... Also, multimedia messages are convenient when it is not possible to use more modern methods of transferring information - Wi-Fi and WhatsApp.

The question of how to set up MMS is asked by the subscribers of all operating operators... The configuration system for sending multimedia messages is approximately the same for all operators. In order to be sure that the function will become available and can be used, it is necessary to make all possible settings, which include the following three steps:

• Step 1 - you need to activate the service;
• Step 2 - set up account;
• Step 3 - check your phone settings manually.

Consider the features of connecting the service and setting up an account within each mobile network... Step 3, which includes manual device configuration, will be considered separately - it does not depend on the operator.

Configuring MMS on Tele2

The question of how to set up MMS on Tele2 will be resolved after you choose any of the following methods:

After completing the necessary actions, the service will be connected and the account settings will be activated.

Setting up MMS on MTS

MTS users can also set up MMS automatically. In order to connect the service and activate required settings, you need to choose a method that is most suitable and convenient for you:

1. Make a call to 0876.
2. Send a free message with the text "MMS" to number 1234.
3. Dial the command * 111 * 18 #.
4. Use an assistant.

The settings received in the SMS message must be saved on your device.

Configuring MMS on Beeline

The question of how to set up MMS on a phone operated by Beeline is solved by very simple and fast ways: The first way is to activate the service called "Three services package", which includes WAP / GPRS / MMS. You can do this by dialing the command * 110 * 181 # and the call key on your phone. This will enable the service and activate the account settings. The second way is to activate the service in your personal account.

Configuring MMS on Megaphone

Megafon provided subscribers with ample opportunities to manage the settings of their phone.

Therefore, the question of how to set up MMS on a phone with a Megafon SIM card is not a problem. Choose the method that is most convenient for you:

• Send SMS with number 3 to number 5049.
• Use the self-government service * 105 #, where then send a request 6 (Settings) - then 1 (Phone settings) - and 1 (MMS).
• Order settings on the company's website.

Setting up your phone manually

This step is necessary in order not to hesitate anymore and to be sure that multimedia messages will be sent from your phone without unnecessary hindrances. It consists of several actions:

1. In the phone menu, find the "Settings" ("Options") tab, then "Configuration".
2. Check the MMC message configuration parameters:

• access point in Tele2 - mms.tele2.ru, in MTS - mms.mts.ru, in Beeline - mms.beeline.ru, in Megafon - mms;
• username in MTS and Beeline is the name of the company in small with Latin letters, in Tele2 - absent, in Megafon - mms;
• the password in MTS and Beeline is the same as in the username, in Tele2 it is absent, in Megafon - mms;
• authentication type - select the "normal" value.

Further actions:

1. Enable the new account as default.
2. Reboot your device.
3. To register your number in the network as an MMS user, after turning on the phone, send a multimedia message to your phone

Setting up MMS on iPhone

The question of how to set up MMS on iPhone can be solved by performing a few manual steps.

1. Order a service:

• operator MegaFon - send SMS with the text "gprs" to the number 000890;
• operator Beeline - make a call to the number 067409181;
• mTS operator - send SMS with the text "GPRS ON" to the short number 0016;
• operator Tele2 - make a call to toll free number 693.

2. Connect the device to a PC with Internet access and running iTunes app... Agree with the offer “Download updated settings". If there is no offer, then the service is configured or the operator is not supported.

3. In the phone menu, open the "Settings" tab, then go to "General", select "Network", go to the " Cellular network».

1. Enter the required values:

• Access point (APN): MTS operator - mms.mts.ru, Beeline - mms.beeline.ru, Tele2 - mms.tele2.ru, Megafon - mms.
• Username in Beeline and MTS - the name of the company in small Latin letters, in Megafon and Tele2 is absent.
• The password is the same as the username.
• MMSC: Tele2 operator - http: // mmsc: tele2.ru, Beeline, MTS, Megafon.
• MMS proxy: Beeline operator - 192.168.94.23:8080, Megafon - 10.10.10.10:8080, MTS - 192.168.192.192:8080, Tele2 - 193.12.40.65:8080.
• The maximum size is 512000.

So the MMC is configured on your device. Use the service with pleasure!

On modern phone models, most of the settings are made in automatic modebut sometimes it crashes and some parameters are not activated. On older phones, you often have to manually configure various features. Those who like to share photos and videos via SMS should check the settings. We will tell you more about how to set up MMS on MTS in this review.

Description of the service and the cost of MMS messages

Almost all tariff proposals of the MTS company include the service of using MMS messages. Despite the fact that today the majority of subscribers prefer to send media files through various social networks and instant messengers, the use of MMS messages is still as popular as ever. The advantage of this way of sending media files is the ability to share photos with friends without having access to the Internet. You don't need to have an internet connection on your phone to send MMS.

Setting up and connecting the service is free of charge. Sending files is charged according to the rates for this service at your tariff. Many tariff plans offer bundled MMS, as the cost of a bundle is cheaper than sending an MMS without a bundle. On average, the cost of one message is 7 rubles. Active users of MMS messages can purchase a package of 10, 20 or 50 MMS or activate the "MMS Plus" option.

The cost of packet MMS is as follows:

• 10 MMS - 35 rubles,
• 20 MMS - 60 rubles,
• 50 MMS - 110 rubles.

By activating the package, you can share media files at a better cost.

Automatic MMS configuration

After installing the SIM card on the phone, all the necessary parameters will already be saved in the mobile device. But if MMS messages are not sent, then you need to configure them. There are two ways to set up MMS messages on the MTS SIM card: in manual and automatic mode.

Automatic configuration of MMC can be performed through a computer by going to the official portal of the MTS company in the settings section. After following the link, enter phone number, to which the necessary parameters will be sent to you shortly. Next, you need to save them and restart (turn off, then turn on) the phone. Now MMS messages are configured and you can test the service performance by sending a picture to another subscriber.

Manual MMS configuration

If the parameters were not sent to you or they could not be saved, then you will need to configure messages manually. Depending on the type mobile device the names of the sections and the parameters themselves may differ. Below we will tell you in more detail how to set up MMS on the most popular operating systemsoh.

MMS settings on the MTS SIM card for Android

1. Go to the item "Wireless networks",
2. Click on the "Internet access points" column,
3. Click on the word "Create APN".

To create an APN, use the following data:

• Profile (name): MTS MMS
• Initial (start) page: http: / mmsc
• Data channel: GPRS
• Access point: mms.mts.ru
• IP address: 192.168.192.192
• Wap port x: 9201
• Wap port 2.0: 9201 (8080)
• Username and password: mts

After completing the manual settings, send the MMS to the phone number 8890. Sending a message is free.

MMS settings on the MTS SIM card for iPhone

1. Select the "Settings" section on your mobile phone,
2. Go to the item "Cellular",
3. Open the "Data Options" section,
4. Click on the sub-item "Cellular data network",

Parameters of the "Cellular data" section:

• APN: mts.ru

MMS parameters:

• APN: mms.mts.ru
• Username and password: mts
• MMSC: http: / mmsc
• MMC proxy: 192.168.192.192:8080
• Maximum message size: 512000
• URL: MMS UAProf

Parameters of the "Modem mode" section:

• APN: mts.ru
• Password and username: mts

After completing the manual settings, send the MMS to 8890. Sending a message is free.

MMS settings on the MTS SIM card for Windows Phone

1. Open the "Settings" section on your mobile phone,
2. Go to the "Data Transfer" section,
3. Click on the sub-item "Create (add) mms access point",
4. Then fill in all the fields in accordance with the instructions below.

Access point setting:

• Access point: mms.mts.ru
• Password and username: mts
• WAP gateway: 192.168.192.192
• Gateway port: 8080
• MMS Center (URL): http: // mmsc /
• MMS Center Port: 8080
• IP type: IPv4v6

Attention: After making the settings, save them, then turn off and turn on the mobile device.

Why are they not sending MMS?

If all the parameters are configured correctly, and MMS are not sent, then try the following:

1. Disable iMessage. Go to the "Settings" section, select "Messages", scroll the slider next to the word "iMessage". If this function is enabled, MMS messages will not be sent. To send you have to switch this mode.
2. Enter your number in phone settings... In the "Phone" section, select "My number" and write down your phone number. Then save the parameters.
3. Check if the "Cellular Data" option is connected. Select the item "Cellular" in the menu, then next to the function "Cellular data" check the position of the slider.
4. Switch to 3G mode. Under Cellular Data, select Voice & Data and switch the slider to 3G. Changing this channel is only necessary if you are using 4G mode. Unfortunately, in the last form of the mode, receiving and sending MMS is not possible.
5. Reset network settings and manually set new MMC parameters.

If manual MMS settings cannot be set on the phone, contact the company's technical support by calling 0890 and ask the employee to send the settings. The employee will send them via SMS. You can also come to the salon cellular communication and seek help from the company's specialists with a mobile phone and a valid SIM card. The staff will help solve this problem.

How to watch MMS

You can view MMS only on mobile phones or on tablet devices, if this service is installed on both of them and all settings are made. On outdated phone models, such messages often open incorrectly, for example, color pictures can be displayed in black and white shades, or the user will receive a regular SMS with a link to this media file, which can only be opened if there is an Internet connection. Moreover, such a link leads to the MTS portal, respectively, after clicking on the link, you will first need to specify a login and password, and only then the picture will open. As you understand, this way of viewing files is very inconvenient, so users of old phone models are better off using various instant messengers and social media for viewing multimedia. And this is only possible if the phone supports the Internet access function.

Many users of one of the most popular cellular operators, often ask themselves how to set up MMS on Tele2. This issue usually requires the most prompt solution when you urgently need to exchange audio recordings, photographs, as well as various multimedia files. To connect the services for receiving and sending MMS, it is allowed to use manual or automatic option... First of all, you should pay attention to general information by connection.

Before configuring such an option, you need to take into account the specifics of this operation. Here are the most basic ones:

• The service becomes authorized after the standard activation of the SIM card;
• If a automatic activation did not happen, you can call 610;
• To write or photograph and send the desired MMS, you should first make sure that the device at your disposal ideally supports this option;
• If the phone for some reason does not support this function, viewing is carried out on a special site in the MMS-Gallery section. The main condition here is the presence of a regular and high-quality image in the content;
• Videos and pictures that are accompanied by audio recordings cannot be opened in the gallery;
• The MMS option will be able to work after setting up a high-quality Internet connection.

All these are simple conditions for compliance and fulfillment. If you make all the required settings, it is allowed to get a preferential opportunity to exchange messages between users of the MMC category.

How to set up MMS on Tele2 automatically?

To get automatic setup desired option, nothing needs to be done. The service becomes available after the standard activation of the purchased and issued SIM card. In just a couple of minutes, all the necessary options will be entered into the available device.
If for some reason the automatic installations were rejected for some reason, the user has the opportunity to restart them. There are two ways to do this:

1. A call is made to 679 and after a short wait the operator will connect.
2. There is an opportunity to use the functionality personal account, you can get there from the company's website. In the profile, you need to go to "Tariffs and services" and "Settings", and then find and activate the service related to receiving and sending MMS.

After sending requests to the phone, the main parameters for the settings come. To start the service, you just need to install required parameters, save everything and restart the device.

How do I set the MMC option manually?

If at the automatic level it was not possible to install the desired option, the necessary parameters will need to be entered manually. Especially often a similar problem arises before the owners of phones of different non-standard models.

For manual setting MMS function, you will need to send a special request in the form of a combination * 202 #.

Important! If there is no time or desire to activate the service on your own, if there is simply not enough knowledge and skills, you need to contact the nearest communication salon for help.

For a nominal fee, the question of how to connect MMS on Tele2 will be resolved.

How to set up MMS Tele2 on all iPhone models?

It is not difficult to configure the function of receiving and sending compiled MMS on smartphones of the iPhone category. You will need to perform a few simple operations:

• You need to go to the basic settings of the phone.
• Visit the received data network.
• A completely new access point is being created for APN access - mms.tele2.ru, MMSC - mmsc.tele2.ru, as well as MMS proxy - 193.12.40.65:8080. Other fields do not require filling.

If done correctly, the function will work without any problems or failures. MMC messages are allowed not only to be sent, but also received in any of their formats.

It is possible to send not only text, but all kinds of photos. To implement this process, you will need to activate the icon with the camera. Then the user is automatically directed to the folder with the stored files. In all OS categories iOS setting is identical. Only the names of the points and their location may differ slightly.

How much does MMS cost on Tele2?

The mobile operator Tele2 does not offer any impracticable and special conditions for the implementation of MMS without making an additional payment for connecting the option. Any subscriber who has previously passed standard authorization can send a multimedia message.

Answering the question how much it costs to use and send messages, it can be noted that no more than five MMS per day can be sent free of charge. All others will be charged at a cost of about 50 kopecks per message. This is a quite affordable price for any Tele2 subscriber.

Conclusion

The service can be connected without any problems for phones running for different operating systems. It could be standard Android or IOS. If the option is connected correctly, messages can be viewed through a computer, but a message can be received on the phone, and completely free of charge.

To send videos and music in messages, you need to know how to set up MMS on Android. Automatic settings for popular smartphone models are sufficient in most cases. If you cannot access the network and send files, you may need to enter information manually.

Some subscribers ask how to set up MMS on Android to the nearest office of their operator. Another option is to call the operator on service number... The disadvantage of this method is a long wait.

When the autoinformer finishes speaking the menu, a transition to the line with the consultant will open. After accepting the application, the subscriber is sent a notification with the parameters. They should be saved, then the device may need to be rebooted. Sometimes activation is requested: you will have to call the consultant again. You can save time if you enter the settings yourself.

How automatic tuning works

The advantage of automatic MMS configuration on Android is that no subscriber's participation is required. When registering in the network, after installing the SIM card (and in some cases entering the PIN code), a message with ready-made parameters is sent to the phone. You need to save it, then you can use the Internet and send multimedia messages.

The downside to automatic debugging is that it is available only once - during registration. If the device is successfully connected to the network, there is no need to re-configure it.

Operator assistance in connecting MMS

If the automatic setup was not successful, you should contact your network operator for help on how to set up MMS on Android. This can be done free of charge by calling the service number. The number of requests is not limited here.

Megafon customers can contact a consultant for help by calling 0500. When the operator answers, he needs to clearly explain the situation and say what difficulties arose with.

In Megafon's communication stores, you can configure the parameters of your mobile device for free. To search for the nearest office, the command * 123 # "Call" is provided.

A Tele2 subscriber can order automatic tuning. To do this, you need to call the service number 679.

Help for Beeline and MTS subscribers

Before setting up MMS on Android manually, you can call the Beeline operator by calling 0611. The call is free of charge. You can also call on federal number 8 800 700 0611 .

The MTS operator has a short support service number 0890. From phones of third-party operators or from stationary devices, you need to call the federal number 8 800 250 0890.

Instructions for subscribers Motive and Yota

For network users Motive in how to set up MMS on Android, the operator will help short number 111. From a mobile or landline phone, you can call the federal number 8 800 240 0000. But this is not the only service.

Automatic configuration can be ordered through # 919 "Call". The disadvantage of this service is that with a large number of calls, you will have to wait about two hours for sending parameters.

Another option is to send the request through a message. To 0111, send a text indicating the device model, the service that needs to be connected (in our case, MMC) and your email address... The parameters will come to it.

For users yota networks there is also a support service. The subscriber can ask his question via SMS by sending a request to the number 0999. You can get advice on the operator's website or in a special mobile application.

Entering parameters manually on Megaphone

You can set up MMS on Android through the menu items. Its titles vary in different models smartphones. Basically, you need to go to the following points:

1. Settings.
2. Wireless network.
3. Mobile network.

Standard parameters have been prepared for Megafon subscribers:

MMS cost may vary depending on conditions tariff plan... Special offers from the Megafon operator will help to reduce the cost of sending multimedia messages. There is no charge for incoming MMS.

Settings for Tele2 users

To send music and pictures from the Tele2 number in messages, the operator provides the following parameters:

To send MMS from your Tele2 number in the future, you will need to register in the system. To do this, after entering all the data, you need to send a multimedia message to yourself or another user.

If registration is not completed, the phone will receive not incoming MMS, but links to go to the Gallery. The same links will also come when you send a multimedia message to a device that does not support this function. When you start working with MMS Gallery, an instruction with a sequence of actions will be displayed on the screen.

How to connect sending MMS for a SIM card Beeline

First, look for the name “Beeline MMS” in the list of profiles. If it is not displayed, proceed to creating a profile with this name. For a SIM card Beeline, the parameters are indicated below:

To complete the operation, you need to go to the messages menu and select "MMS Settings", then click on the connection profiles. You need to make sure that the newly created Beeline MMS is selected.

After carrying out all the operations, it is worth checking the result. Create a message, add a melody, photo or video to it and send to the subscriber. If the MMS has been delivered, it means that all actions were performed correctly. Upon notification of an error, the entered data should be checked again.