Instructions for installing the official single-file firmware on Samsung Galaxy J5 (SM-J500x).
Drivers and programs
Attention!
To install the official stock firmware on the Galaxy J5 and return the phone state ("Settings"> "About device"> "Properties"> "Device status") to "Official" after switching from custom firmware and thereby return the ability to receive updates over the air, it is enough follow the instructions provided.
Installation instructions
Unpack the downloaded archive into the Odin PC folder for convenience. The file in the ".tar" or ".tar.md5" format must be kept and "SS_DL.dll" can be deleted.
Reset device data.
To do this, go to the settings in the section " Back up and factory reset", Select the item" Data reset» > « Reset device", Enter the PIN-code (if one is set) and press the button" Delete everything". The phone will restart.
Run Odin PC as administrator.
Put the device into download mode ( Download Mode).
To do this, you must simultaneously hold down the Volume Down key, the Home button and the Power button. Then wait until the phone restarts and accept the warning by pressing the Volume Up key.
In this state, connect the smartphone to the computer. Odin should light up the inscription “ COM».
Press the button " AP»And select the TAR-archive of the firmware.
Items " Auto reboot" and " F.Reset Time" must be activated, a " Re-Partition", If active - must be disabled.
Press the button " Start". The process of installing the firmware will begin.
At the end of the operation, if everything went well, the message “All threads completed. (succeed 1 / failed 0) ". The phone must be rebooted manually by holding down the power button until the screen turns off. The device may take up to 5 minutes to boot up for the first time.
ATTENTION!
If the device does not boot for a long time or the data has not been reset, it must be performed from the recovery.
To do this, simultaneously hold down the Volume Up key, the Home button and the Power button. After downloading, select the item " Wipe data / Factory reset", and then - " Reboot system now". If after these steps the device also freezes at startup, you need to reflash it again.
If the J-Link firmware has crashed ...
Created on 04/28/2015 12:11 PM
If the J-Link firmware has crashed ...
Once I updated Keil and he happily informed me that I needed to update the J-Link firmware, but an error occurred during the update, the programmer became unusable. A quick inspection showed that at that time I had a package from SEGGER version 4.92, and Keil had a library version 4.96. One way or another, I had a beautiful plastic vegetable in my hands that did not want to be identified in the system.
We open the programmer and easily find the unsoldered jumpers ERASE and TST.
Before starting the flashing, it is better to unsolder these jumpers normally.
We transfer the device to the firmware download mode. For this:
disconnect USB, close ERASE
connect USB, wait a couple of seconds,
disconnect USB, open ERASE, close TST,
connect USB, wait 10 seconds
disconnect USB, open TST.
Thus, we cleared the memory of the chip and restored the bootloader. When the device is connected to a computer, a COM port should appear in the system.
Download and install the AT91-ISP package from atmel.com. Replace the port driver installed by the system with the driver located in the C: \ Program Files \ ATMEL Corporation \ AT91-ISP v1.13 \ sam-ba 2.9 \ drv "atm6124.sys ATMEL AT91xxxxx Test Board" folder (for Windows 8, you need to disable digital signature verification drivers). Let's run Sam-ba to make sure everything works.
All that remains is to flash the J-Link. Launch SAM-PROG. Select the file with the firmware and press the "Write Flash" button or by checking the "Auto-mode" checkbox, connect the device.
Download the current package for J-Link from segger.com (at the time of this writing, v4.98) and install it. We connect J-Link and update the firmware on it with regular means and correct the serial number of the programmer by executing the exec setSN = command in the J-Link Commander<ваш серийный номер>.
The programmer is ready to work.
Instructions for installing the official single-file firmware on Samsung Galaxy J2 (SM-J200x).
Drivers and programs
Attention!
To install the official stock firmware on the Galaxy J2 and return the phone state ("Settings"> "About device"> "Properties"> "Device status") to "Official" after switching from custom firmware and thereby return the ability to receive updates over the air, it is enough follow the instructions provided.
Installation instructions
Unpack the downloaded archive into the Odin PC folder for convenience. The file in the ".tar" or ".tar.md5" format must be kept and "SS_DL.dll" can be deleted.
Reset device data.
To do this, go to the settings in the section " Back up and factory reset", Select the item" Data reset» > « Reset device", Enter the PIN-code (if one is set) and press the button" Delete everything". The phone will restart.
Run Odin PC as administrator.
Put the device into download mode ( Download Mode).
To do this, you must simultaneously hold down the Volume Down key, the Home button and the Power button. Then wait until the phone restarts and accept the warning by pressing the Volume Up key.
In this state, connect the smartphone to the computer. Odin should light up the inscription “ COM».
Press the button " AP»And select the TAR-archive of the firmware.
Items " Auto reboot" and " F.Reset Time" must be activated, a " Re-Partition", If active - must be disabled.
Press the button " Start". The process of installing the firmware will begin.
At the end of the operation, if everything went well, the message “All threads completed. (succeed 1 / failed 0) ". The phone must be rebooted manually by holding down the power button until the screen turns off. The device may take up to 5 minutes to boot up for the first time.
ATTENTION!
If the device does not boot for a long time or the data has not been reset, it must be performed from the recovery.
To do this, simultaneously hold down the Volume Up key, the Home button and the Power button. After downloading, select the item " Wipe data / Factory reset", and then - " Reboot system now". If after these steps the device also freezes at startup, you need to reflash it again.
Detailed, step-by-step instructions on how to flash a Samsung Galaxy J1 (2016) SM-J120 smartphone to a new official or custom firmware. Getting Root superuser rights on Samsung Galaxy J1 (2016) SM-J120, installing custom TWRP Recovery.
Installing the official firmware on the Samsung Galaxy J1 (2016) SM-J120 smartphone using the Samsung Odin service program. In order to install a new firmware on a smartphone, you first need to download several files to your PC:
Download the latest Official Firmware for Samsung Galaxy J1 (2016) SM-J120
Official service multi-file firmware J120FXXU1APH1
official single-file firmware J120FXXU1APH1
Before flashing your phone, you first need to decrypt it.
To remove the lock from Samsung Galaxy J1 (2016), you need to disable the reactivation lock. Go to "Settings" - "Lock screen and protection" - "Find phone" and disable "Activation lock" Before and after the firmware update procedure, you must do a general reset of the device to the factory settings in order to avoid all kinds of errors and slowdowns of the interface.
When performing this procedure, all your data and files will be permanently deleted.
Option 1: On the device, open "Settings"> "Back up and reset"> "Accounts"> "Reset data"> "RESET DEVICE" and click "Delete everything"
Option 2: Turn off the device, press and hold the "Volume Up", "Home (Center)" and "Power" buttons and after a few seconds the "Recovery" menu will appear. In the "Recovery" menu, select "Wipe data / factory reset" -> "Yes - delete all user data", all user data will be deleted. After completing the process, select "Reboot system now" and the device will start to reboot.
You can skip this step, but remember! If you do not reset the data, after the update, “lags” and unstable operation of the device as a whole may appear due to the tails of the previous firmware, and more recently, before completely resetting the smartphone, you also need to delete the Google account, otherwise the smartphone may be blocked.
After you have downloaded everything, unpack the archive with the driver for Galaxy J1 (2016) and install it. Then unpack the Odin archive and firmware.
Run the program for the Galaxy J1 2016 Odin firmware as administrator. To do this, hover over Odin and right-click and select "Run as administrator", then click "Yes".
After starting Odin, we arrange the firmware files in the following order:
Insert the BL ……… .tar.md5 file into the "BL" field
The AP file ……… .tar.md5 is inserted into the "AP" field
The CP file ……… .tar.md5 is inserted into the "CP" field
Insert the CSC file …… ..tar.md5 into the "CSC" field
We check that the “ticks” were only in the fields “Auto Reboot” and “F. Reset Time "
We transfer the Samsung Galaxy J1 SM-J120 phone to the firmware mode. To do this, turn off the phone and then press and hold the "Volume Down", "Home" and "Power" buttons and after the menu with a yellow triangle appears, press the "Volume Up"
We connect the smartphone using the supplied USB cable to the PC and in the Odin program, in the upper left corner the inscription “COM” should appear highlighted with a blue background, and then press the “Start” button.
Note: If for some reason your PC does not recognize your device, try reinstalling the driver and / or try other USB ports.
The process of flashing the smartphone has started. After successful flashing, the device will reboot automatically and “Finish” will appear in the Odin program.
Installing custom recovery TWRP Recovery v3.0 on Samsung Galaxy J1 SM-J120
And so let's start installing custom recovery on samsung j1
If you have not yet installed the Samsung drivers on your PC, then download and install. Then connect, using a standard USB cable, your smartphone to the computer. After the PC recognizes the phone automatically, additional drivers and updates are installed.
We need the Odin 3 program, download Odin
Then download the very custom recovery for Samsung J1 SM-J120
FOR J120 F :
Download TWRP Recovery recovery.tar.md5
FOR J120 H :
Download TWRP Recovery TWRP J120H
Turn off your smartphone, and then (on off) press and hold the Down Sound + Power + Home key until the phone boots into Odin mode (Download Mode). You will see a warning, confirm your desire to boot in this mode by pressing the "Volume up" key.
Put the phone into Odin Mode, connect it to the PC using a standard USB cable.
Run the Odin 3 flasher on the PC as administrator
In the AP line, specify the path to the previously downloaded file with custom J1 TWRP Recovery with the extension “.img.tar” and select it
Uncheck the “auto reboot” box and press start (the phone must flash, the firmware time is no more than 30 seconds, the result should be like this (succeed 1 / failed 0);
Until the flashing process is complete, do not touch the Smartphone, usually the flashing lasts no longer than 30 seconds.
Without turning on the gadget in a working state, right from the Download mode, go to the newly installed TWRP Recovery by holding down three buttons (volume up + home + power button, when the Samsung inscription appears, release the buttons).
Everything! We rejoice.
Installing custom firmware on Samsung Galaxy J1 SM-J120
To install custom firmware on a Samsung Galaxy J1 phone, you need a custom TWRP Recovery, if you don't have one, see the paragraph above.
Download to your PC any custom firmware that you like, for example -
Introduction
This article will focus on self-updating software (in normal mode) in phones and smartphones Nokia at home without using the Internet using the program J.A.F. 2.0 test ... This firmware method has been tried more than once, and it will not take you much time. The instruction is written in a language that is understandable enough for beginners.
What do we need?
- - J.A.F. suite
- The firmware itself for your Nokia phone (can be found on our website in the section).
- Data cable to your phone.
- Charger.
- Desire to flash.
- All Nokia-related programs (Nokia Ovi suite, Nokia PC suite, Nokia Software Update, their various utilities, etc.) must be removed on the computer. Otherwise, problems that we do not need may arise.
For cleaning the registry recommended program Vit Registry Fix(office site).
- About installing the program JAF. 2.0 You can find out on our.
- Before flashing and running the "JAF" program, it is strongly recommended to disable anti-virus programs that may interfere with the stability of the program.
- After installing "JAF", install the unified driver.
2. We connect the included phone. Installing the driver (happens automatically when connected).
Windows of this kind will be displayed in the lower right corner of the monitor (during driver installation).
3. Press the button INF and read information from the phone.
4. Download the firmware files of the required version for your RM -XXX.
5. Make a backup of RM by selecting the checkbox on the field Read PM and pressing the button SERVICE.
We drive in the starting address - 0
And the final one is 500, we press OK.
We are waiting for the end of the process.
If, when you press the INF button, several lines appear and the RM is not readable, skip the RM read item and proceed to the firmware.
Firmware
Push the button USE INI if you have installed full firmware package and latest version of INI file.
If the versions of the required files or the product code do not match, select the files manually. Check the box Manual Flash and Factory Set.
Selecting the firmware files... The main MCU firmware file must be renamed to the extension .C0R for the program to see it.
Then we select the PPM and CNT files (there may not be a CNT file for smartphones).
After the files are selected, click FLASH and once again check the correctness of the selected files.
If everything is correct, click OK.
The firmware process begins, if everything is fine, the phone will turn off and the search for new drivers for the firmware will start, since WINDOWS is clean, everything goes on the fly. If any error appears, read the complete
