The d link dir 615 wireless router is a convenient "home" router that provides Wi-Fi connection at speeds up to 300 Mbps using the 802.11b, g and n standards.
Externally, the model is a "classic" stationary router with two external antennas and connectors for cable connection of external devices. Of the functional features, we can note the built-in firewall, the ability to work with SIP protocols and support for all wireless communications.
D-Link Dir-615 provides a stable Internet connection when working with providers such as Rostelecom, Dom.ru, MTS, Beeline, etc. Also, the device can be used to connect to the worldwide network via a dedicated line and Dial-up technology - in this case, additional modem configuration is required.
d link dir 615: specifications
dir 615 wifi router works in the frequency range 400 ~ 2483.5 MHz.
The rear panel of the device has one INTERNET port for connecting an Ethernet cable provided by the provider and four LAN connectors for connecting to a router and other stationary devices via a network cable.
The dir 615 modem also supports static IP routing.
The dir 615 front panel contains router status indicators:
- - separately "standing" power indicator;
- - an indicator of the activity of the Internet connection (if this LED is off, it means that the Internet from the provider does not come to the router: there may be a line break or a technical failure of the service provider's equipment);
- - wifi indicator, the green light of which characterizes the ability to connect to the d link dir 615 router wirelessly;
- - four LAN-indicators that light up when the corresponding LAN-connector is active;
- - WPS indicator that lights up when activated.
How to connect a d link dir 615 router?
Installation of the d link dir 615 router is carried out according to standard instructions, which are identical for most network devices.
- 1. First, provide "power" of the device from a standard 220V power supply. To do this, plug the power adapter plug into the round connector on the rear panel of the device, and plug the adapter "plug" into any AC outlet.
- 2. Turn on the router using the ON / OFF button and wait for the router OS to load - the corresponding indicator on the front panel of the device should light up.
If your router has ever been in operation, it is recommended that you reset the d link dir 615 settings to factory settings. To do this, press the RESET button recessed into the case with a needle or a paper clip, hold it down for 10-15 seconds and wait for the device to restart.
- 3. For the initial configuration of d link dir 615, a "hard" connection of the router to the computer is required. For cable connection, you can use the patch cord supplied with the device or a piece of twisted pair, crimped on both sides with RJ 45 connectors.On the one hand, the network cable must be connected to any LAN connector on the back of the router, and on the other, to the network card port of your stationary computer or laptop.
- 4. To connect d link dir 615, you will also need the appropriate settings for your computer's network card. Step-by-step instructions for Windows7 and Windows8 are presented in the article, and configuring network settings on Windows XP is described step by step in the article.
How to configure the d link dir 615 router yourself?
The d link dir 615 router is configured through the device's web interface, and you can enter the menu from a computer connected to the router through any web browser.
To do this, enter the static IP address of the device in the address bar (in most cases this is a combination of 192.168.0.1), which is indicated on the device's service label.
Press Enter and in the authentication window that appears, enter the username and standard password dir 615.
The d link dir 615 router has a default password - admin and login - admin. If the settings have been changed, and the user subsequently forgot the password of the router, it is enough to reset the device settings to the factory settings and enter the standard password.
At the first stage, the Internet is configured via the d link dir 615 router. To do this, you need to specify:
- - what type of Internet connection the provider provided you;
- - whether it is necessary to specify the login / password when connecting to the global network;
- - what parameters "to the Internet" have been provided to you by your communication service provider.
These parameters are specified in the contract with the provider, and you can also check them in the provider's 24-hour support service.
If there is already an automatically generated WAN connection in this window, it is recommended to delete it.
- - for PPPoE connection in the opened PPP subsection, enter your username and password for connecting to the Internet from the agreement with the provider;
- - for a connection of the Static IP address type, you will need to specify the IP address, Netmask, gateway IP address and Primary DNS server (also from your contract);
- - for dynamic IP in the IP column, uncheck "Obtain DNS server address automatically" and enter the primary DNS server provided to you.
Dir 615 wireless router: wifi setup
Setting up wifi on the d link dir 615 router is carried out in the corresponding menu tab:
In the main window of the router settings, click the "Wi-Fi" button and go to the "Security settings" section.
Please note that you should set a complex and unique password for the Wi-Fi in order to secure the wireless connection.
Router dir 615: setting up iptv
To connect iptv on a wireless dir 615 router:
- 1. Plug the TV box into a free lan port of the device.
- 2. In the LC, select "Advanced settings" and the heading "IP TV".
- 3. Select the appropriate device port in the "Iptv Configuration Wizard" and click the "Change" button.
This completes the iptv setup successfully.
Connecting your home to the Internet is very simple and often even cheap. However, not all Internet companies provide router configuration for you. Therefore, the first user, the buyer, has to independently configure the router.
To avoid any setup problems, just follow our simple instructions for setting up the D-Link DIR-615.
Features and appearance of the router
There is almost nothing to say about the characteristics of the D-Link 615, because they are extremely similar for all such devices. 802.11n technology is used, antennas are built-in, 4 network ports, the operating frequency is about 2.4 Gigahertz. Data transmission speed through cable up to 100 megabits per second, through wireless network up to 300 megabits per second.
On the front panel there are several, or to be more precise, 8 lamps that act as indicators:
- The first indicator is "Power", this light is responsible for powering the device, connecting to electricity.
- The indicator is signed "WPS", it shows the status of this function.
- Light "Internet". It's not hard to guess what she is responsible for. This is the state of being connected to the world wide web.
- The rest of the indicators are responsible for ports. The first one is "WLAN". This is wifi mode.
- 4 more ports for connection via LAN cables.
There is only one “WPS” button on the side panel, which can make a quick connection.
On the back panel there are two special places for attaching our device to the wall. And below are the various ports and buttons:
- First there are 4 local ports where you can insert a network cable to connect your home computer directly.
- One port for internet connection.
- The button is located inside the "Reset" hole. To press it, you need to use some thin object, such as a paper clip. Hold this button for 7-10 seconds. After that, the device will be restored to factory settings.
- Power connector for the router. This is where you plug in the power cord with the other side of the socket.
- Power on / off key of the router. This button can be used to reboot the router.
After we know exactly the location of all the connectors and indicators we need, we can proceed to installing the D-Link DIR-615 router, we will configure it a little later.
Replacing the router
We choose a place that would be approximately in the middle of our house or apartment. This is to ensure that the signal is approximately the same in different rooms. There should be an outlet nearby and an Internet cable should reach there.
We attach it to the wall, insert the power supply, turn it on with the power button, connect a laptop or computer to it via the LAN port. There is one more point here that is important in further customization. If the Internet immediately appeared on the computer, then you can immediately determine which IP address your provider has.
If the Internet immediately appeared, then you have a dynamic IP address. Through the WLAN wire, the provider immediately redirects incoming traffic to you.
There shouldn't be any questions about how to connect or how to install a 615 router for Rostelecom, because each connector meets its own wire.
To make a static IP, you need to forward D-Link 615 ports. Let's go directly to the D Link settings. We will write about how to open ports on a D-Link router in a separate article.
Full device customization
To begin with, immediately after connecting the 615s router to your computer, you should reset the settings. So, to set up D-Link DIR-615 from the very beginning:
Reset
To reset the settings, you just need to hold down the "Reset" button located on the back of the device in the hole. Press and hold the key for 7-10 seconds. All settings of the D-Link DIR-615 router will become factory settings. This is an especially important step for those who have purchased the device after someone else has used it.
You can also reset the password for those who have forgotten their password. To set the default password and login on the D-Link Wi-Fi router. Then the reconfiguration is performed.
Firmware problems
After that, it should be noted that routers usually have an old firmware version, the oldest. You can also work with it, but it's better to save your nerves and strength - download the update. We are downloading the latest firmware to keep up with the world.
On the underside of our device is a serial code and a bunch of other update information. We are interested in the line "H / W Ver.:**". The asterisks should be replaced by the version of your D-Link DIR-615 router. We have it K1.
Now, before entering the settings, go to the official website http://ftp.DLink.ru/pub/Router/, do everything clearly according to the screenshots. Here's an example of updating K1.
Now we have the software for our router, which we needed to update. Now, in fact, we will learn how to flash a D-Link DIR-615 router.
To do this, go to the settings on the router debugging site in the router settings, this is the address 192.168.0.1 or 192.168.1.1. Enter the name and password - "admin" - these are the factory settings of router D. Now you can see the interface. The firmware version is written on top. If it is version 1.0.0, then go to "Configure manually". Then "System", select "Software update", select the file that was downloaded a little earlier and update the modem.
This completes the flashing.
Debugging WEB connection
We go into the same router settings at 192.168.0.1, enter admin / admin, click "enter". In the updated firmware, at the bottom, click on the advanced settings. Then select WAN from the list, this item is located in the "Network" block.
We press the "Add" button, thereby creating a new connection to the network. Here you need to enter the data provided by your provider. The type of connection, login and password must be specified in the contract, do not forget to clarify these points with him. This is required to connect to an Internet. Click "Save".
Now the Internet should appear on the local network, that is, on those computers that are connected via local LAN cords.
Debugging a wireless network
In the "Wi-Fi" block, click on the general settings. All this is in the same advanced settings, in case anyone has forgotten. Here we press "Enable wireless connection", put a tick and save. As you can see, setting up the D-Link DIR-615 Wi Fi router is a fairly simple task.
After that, in the SSID field, enter the name of your wi-fi, it will be visible to everyone. Write in English. We choose our country, we leave the channel automatic and the mode is the same.
Now in the Wi-Fi block, select the security settings. In the first Wifi setting point, set WPA-PSK2. The next field is where the encryption key is. This is the Wi-Fi password. On the same tab, the answer to the question of how to change the password or how to put a password on Wi-Fi.
Now you have figured out how to configure the D-Link DIR-615 router thanks to our step-by-step instructions.
Related Videos
Fast Internet for you!
Many people think about how to configure the d-link dir-615 router and the reason for this is not the complexity of the configuration, but the popularity of this model. The d-link DIR-615 router stands out against the background of similar devices with an acceptable cost and good quality. If you decide to choose a router of this model, then you need a device with good Wi-Fi coverage and decent internet quality. However, in this article we do not plan to discuss the advantages and disadvantages of this model, now our task is to explain to you how to configure the d-link dir-615 router correctly. In the previous article, we provided instructions for configuring the router, and this model has a lot in common with the d-link dir-615, however, there are enough differences, so we have prepared a separate manual.
How to connect d-link dir-615 router to computer
Before configuring the D-Link DIR-615 router, you need to connect the device to your computer. Basically, the d-link dir-615 connection process does not imply any significant distinguishing features. You need to connect the router to the mains, insert a network cable into any of its LAN ports and connect it with the opposite end to the PC. In the WAN port of the router, you need to insert the cable from the Internet provider. In general, the process of connecting the d-link dir-615 router does not imply any difficulties and any user can cope with this task. The router connection diagram is as follows:
Downloading updates for the d-link dir-615 router
As a rule, d-link dir 615 routers (like most other models) have firmware version 1.0.0. or 1.0.18. This is far from the most recent firmware version and it is advisable to install an update. You can download the latest firmware version on the official D-Link website ftp.dlink.ru. The latest firmware version ensures more stable operation of the router. The update only takes a few minutes and is completely free. Before downloading the firmware, you need to determine which version and revision your router is equipped with. To do this, look at the sticker on the back of the router.
After you determine the revision version of the D-Link DIR-615 router, you need to go to the official D-Link website at ftp.dlink.ru and follow the following path: pub - Router - your router model - Firmware - router hardware revision ... Find the bin file (and there is a firmware) and download it. This is how the process looks like on the example of the version of revision K1:
We perform a flashing of the D-Link DIR-615 router
The flashing of the router is carried out in the web-interface of the router. To get to this page, enter the value 192.168.0.1 in the address bar of any browser. After clicking on the specified link, a D-Link window should appear, in which you will be asked to enter your username and password. As a rule, by default the D-Link DIR-615 router has the same username and password - admin. If you cannot log in with it, get the documentation for the router and check the details for entering the router interface.
After entering, we are looking for the item "Configure manually", then in the "System" section, click on the tab "Software update". After that, load the previously downloaded firmware file. After downloading the update, the software for the router will update and a new interface will open.
How to debug your internet connection
It should be noted that setting up the connection of the D-Link DIR-615 router to the Internet is possible in two ways - manually and semi-automatically. We will use the second option, but we give preference to it not only for its convenience, but also for the ability to get access to the full functionality.
On the main page of the router interface, we are looking for the "Advanced setup" section, then click on the "Network" tab and select the WAN item.
You should see a window in which you need to select the "Add" item and create a new connection. To do this, you need to specify the type of connection in the form that opens, which may differ depending on the specific provider, usually PPPoE. Although, it is desirable to clarify this point, you can do this on the official website of the Internet provider. Here you also need to specify your login, password, MAC address, MTU. In this section, other parameters are also indicated, if necessary. We recommend not changing anything.
If you do not know any of the mandatory data, you can find out them from the contract with the provider. You can also get the necessary information from the support service, again provided by the provider. Remember to save the settings after entering all the required information. Basically, if you did everything correctly, then an Internet connection should already appear.
How to debug access to wifi in a D-Link DIR-615 router
Despite the fact that the ability to access the Internet should appear after the above steps are completed, the configuration of the D-Link DIR-615 router does not end there. You also need to make the appropriate settings for the router. So, again go to the user interface of the router, in the Wi-Fi section, select "General settings", then "Turn on wireless ...".
After that, go to the "Basic settings" section of the Wi-Fi menu and, opposite the SSID section, enter the name that you want to assign to your network. The final action is to click the "Change" button.
You also need to configure the security settings. To do this, go to the "Security Settings" section, in a new window opposite the "Network Authentication" item, specify the WPA-PSK2 value. After that, in the empty field next to the PSK encryption key parameter, enter the desired password, which will later be used to connect to the network. Do not forget to save the settings by clicking on the "Change" button.
That's all, in general. The D-Link DIR-615 router has been configured. If you have any questions, perhaps you can find the answers in the video below.
appearance of the D-link dir 615 router
The dir 615 router is a popular tool for ensuring constant Internet accessibility for laptops, PCs, tablets, smartphones and other gadgets via a wi-fi network. This router will be an excellent choice for home use or small office space. For correct operation, routers must be configured in a certain way. The configuration method depends on what type of connection the providers offer. If you use a connection using a dynamic IP, then there will be no difficulties here, since it is enough to simply connect the router to work. In this article, we will show you how to properly configure it using the router's settings panel.
In order to independently configure the router for work, you need to perform a few simple steps. First, connect the power cable to the router, turn it on. In case the row of lights on the front of Router D does not light up, you need to turn on the power using the button on the rear panel. If you plan to connect and configure the router via a cable connection, then use the network cable supplied with the dir router and connect the router to your PC.
Appearance of the patch cord Rj 45 (cable included with the router). Cable for connecting the Internet to the router
wAN and LAN connectors of the D-link dir 615 router
We insert the end of the cable into one of the black LAN connectors, of which there are 4 on the router, and the 2nd end must be connected to the output of the network card of a PC or laptop. Your ISP's Internet cable must be connected to the yellow WAN connector.
Resetting old settings
The next step is to make adjustments to the router settings. You need to go to the settings of the router, but before that you need to reset the existing settings, which, quite possibly, have already been made. In order for them not to interfere with the current work, it is necessary to return the dir router to its factory state. To do this, you need to reload the settings. This simple procedure is performed using a thin sharp object, match or needle, with which we press the RESET key located in the device body. The button must be held down for about 10 seconds, this will allow the router to restart the settings.
rESET button D-link dir 615
Router control menu
If you do not know how to enter the d link dir router control menu, then:
- just launch your existing browser
- enter the following IP address of the router: 192.168.0.1.
hit enter
enter the router interface, copy and enter http://192.168.0.1 into the address bar of your browser
A window will appear on the screen asking for a login with a password. Their original meaning is admin \\ admin.
When you enter this data, the settings of the D-link router will open in front of you. If you are there for the first time, then perhaps the entire menu will be presented in English. Using the appropriate options, you can change the language to Russian or Ukrainian.
Choose your preferred language from the drop-down menu
In addition, a window may appear where you will be asked to change the password to exit the settings menu to your own. Enter the appropriate password, but do not forget to write it down somewhere, for example, on your phone, so that you do not lose access to the menu in the future if you need a new router setting d.
Setting up the Internet on the router
After completing all the previous points of the instruction, you will come to the main task - how to configure the router for the Internet. First of all, check which connection method is used by your operator. There may be several of them:
- Dynamic IP
- Static type
- PPPoE
To do this, contact technical support or go to their web page. If the operator supports the dynamic IP protocol, then for your DIR 615 router, the configuration will consist only in the administration of the wi-fi network. The wifi router will start distributing directly from the moment you connect the cable from the operator, and you just need to configure the wi-fi network.
If your provider does not have dynamic IP support, the configuration procedure continues further.
When the window "Address of local resources of the provider" appears, you can add addresses there, if you do not understand this, or you simply do not need them, then the wifi setting continues after you press the "Next" button. A window will appear where you need to specify the name of the connection and login with password. This information is provided by the providers. Pressing the "Details" button opens a menu with advanced settings. If you went there for the sake of interest as a regular user, then you will not need extra settings, so you can ignore this tab.
After that, testing of the Internet connection will begin, where you will be prompted to activate the Yandex.DNS filtering system. If it matters, then you can configure the d link dir 615 router by making changes that can later be changed to the actual ones.
If the Internet did not appear
When, after completing all the steps of the instructions, the router still does not start distributing the Internet, information appears about the nature of the connection "no access to the Internet" or it is impossible to open websites, then check all the settings again, and then configure everything again. You may need to restart your computer.
Common mistakes are:
- Wrong choice of connection type
- Incorrect entry of certain parameters
Let's note one nuance - if before using the router you had a high-speed connection on your computer for connecting to the Internet, now it is no longer necessary. This connection is now in the competence of the router, which installs it and distributes the Internet via cable and wi-fi network.
Conclusion
Setting up and connecting a router with your own hands is a task that can be done by any person. Thanks to these instructions and the intuitive interface of the router with the ability to use technical support from the provider, you will devote very little time to setting up a wi-fi connection.
